Basics of Technical DrawingLaajuus (5 cr)
Code: TE00BR47
Credits
5 op
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Enrollment
12.12.2024 - 12.01.2025
Timing
13.01.2025 - 25.04.2025
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Degree programmes
- Degree Programme in Automotive and Transportation Engineering
Teachers
- Jyri Jänne
Groups
-
PAUTOS24APAUTOS24A
-
PAUTOS24BPAUTOS24B
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
03.08.2024 - 01.09.2024
Timing
02.09.2024 - 20.12.2024
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Degree programmes
- Degree Programme in Industrial Management Engineering
Teachers
- Jyri Jänne
Groups
-
PTUTAS24APTUTAS24A
-
PTUTAS24BPTUTAS24B
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
03.08.2024 - 01.09.2024
Timing
02.09.2024 - 16.12.2024
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Degree programmes
- Degree Programme in Automotive and Transportation Engineering
Teachers
- Jyri Jänne
Groups
-
PAUTOS23APAUTOS23A
-
PAUTOS23BPAUTOS23B
-
LIPATMODValmennusAmmattiopintoihinI
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
01.12.2023 - 07.01.2024
Timing
08.01.2024 - 26.04.2024
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Teachers
- Jyri Jänne
Groups
-
PTUTAS23APTUTAS23A
-
PTUTAS23BPTUTAS23B
-
LIPATMODYrityksenToiminnanohjaus
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
16.07.2023 - 03.09.2023
Timing
04.09.2023 - 14.12.2023
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Degree programmes
- Degree Programme in Automotive and Transportation Engineering
Teachers
- Jyri Jänne
Groups
-
PAUTOS22APAUTOS22A
-
PAUTOS22B
-
LIPATMODValmennusAmmattiopintoihinI
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
02.12.2022 - 23.01.2023
Timing
09.01.2023 - 28.04.2023
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Teachers
- Jyri Jänne
Groups
-
PTUTAS22APTUTAS22A
-
PTUTAS22BPTUTAS22B
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
02.12.2022 - 23.01.2023
Timing
09.01.2023 - 28.04.2023
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Teachers
- Jyri Jänne
Groups
-
PTUTAMS22PTUTAMS22
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
10.12.2021 - 24.01.2022
Timing
10.01.2022 - 29.04.2022
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Teachers
- Jyri Jänne
Groups
-
LIPATMODYrityksenToiminnanohjaus
-
PTUTAS21BPTUTAS21B
-
PTUTAS21APTUTAS21A
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5
Enrollment
10.12.2021 - 24.01.2022
Timing
10.01.2022 - 29.04.2022
Number of ECTS credits allocated
5 op
Mode of delivery
Contact teaching
Unit
Engineering and Business
Campus
Kupittaa Campus
Teaching languages
- Finnish
Teachers
- Jyri Jänne
Groups
-
LIPATMODYrityksenToiminnanohjaus
-
PTUTAMS21APTUTAMS21A
-
PTUTAMS21BPTUTAMS21B
Objective
After completing this study unit student:
- understands technical 2D drawings and masters the basics of 2D drawing.
- is able to measure and mark correct dimensioning to the drawing.
- is able to use typical measurement tools used in a machine shop.
- understands the principles of CAD modelling.
Content
- types of technical drawings
- basics of 2D drawing, projection, section, measurements etc.
- use of basic measurement tools, Vernier caliper and micrometer
- basics of CAD-drawing, introduction to CAD software, exercises
Evaluation scale
H-5